|
|
Please Click on an Image to Select a Sensor Type:
STEP: 1 of 5
|
CHOICE 1
|
Single Ch Gear Tooth Sensor
|
- DETECT GEAR TEETH, 4-32 PITCH
- ONE DIGITAL PULSE PER TOOTH
- DETECTION GAP UP TO .150"
- TRUE 0 SPEED TO 10,000 Hz
- ORIENTATION IS REQUIRED
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CHOPPER STABILIZED HALL EFFECT
- PREDICTABLE MAXIMUM GAP
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 2
|
Hall or Magneto Resistive Switch Sensor
|
- DETECT MAGNETS OR MAGNETIC FIELDS
- DIGITAL OUTPUT, NPN PNP OR RELAY
- DETECT NORTH, SOUTH OR EITHER POLE
- DETECT PRESENCE OR COUNT EVENTS
- RESOLVE LINEAR OR ROTATIONAL SPEED
- TRANSISTOR OUTPUT OR RELAY CLOSURE
- DETECTION GAP UP TO 3"
- TRUE 0 SPEED TO 20,000 Hz
- NO ORIENTATION REQUIRED
- DC POWERED, OPTIONS FROM 2.5 TO 30 V
- POTTED, RUGGED, -40 TO 150 DEG C
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 3
|
Single Ch-Target Tracker Gear Tooth Sensor
|
- DETECT GEAR TEETH, 0-32 PITCH
- DETECT HOLES, BOLT HEADS OR OTHER FERROUS TARGETS
- DETECT LONG OR MISSING TEETH 1 PULSE PER TARGET
- DETECTION GAP UP TO .180"
- NEAR 0 SPEED TO 15,000 Hz
- NO ORIENTATION IS REQUIRED
- DC POWERED, 3.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- NOT CHOPPER STABILIZED (NO CHOPPER NOISE)
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 4
|
Quadrature (2 Ch) Gear Tooth Sensor
|
- QUADRATURE OUTPUT FOR SPEED & DIRECTION
- 2 PULSES PER TOOTH 90 DEGREES OUT OF PHASE
- FOR LINEAR OR ROTATIONAL MOVEMENT
- DETECT GEAR TEETH, 0-24 PITCH
- DETECT MOVING BOLT HEADS OR OTHER FERROUS TARGETS
- DETECTION GAP UP TO .180"
- TRUE 0 SPEED, AND NEAR 0 SPEED OPTIONS
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CHOPPER AND NOT CHOPPER OPTIONS
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 5
|
Speed and Direction Gear Tooth Sensor
|
- 2 OUTPUTS FOR SPEED (OR COUNT) & DIRECTION
- LINEAR OR ROTATIONAL MOVEMENT
- DETECT GEAR TEETH, 0-24 PITCH
- DETECT MOVING BOLT HEADS OR OTHER FERROUS TARGETS
- DETECTION GAP UP TO .180"
- TRUE 0 SPEED, AND NEAR 0 SPEED OPTIONS
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CHOPPER AND NOT CHOPPER OPTIONS
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 6
|
Speed Direction Quad Gear Tooth Sensor
|
- 3 OUTPUTS FOR SPEED (OR COUNT) & DIRECTION
- QUADRATURE SIGNAL AND DIRECTION OUTPUT
- LINEAR OR ROTATIONAL MOVEMENT
- DETECT GEAR TEETH, 0-24 PITCH
- DETECT MOVING BOLT HEADS OR OTHER FERROUS TARGETS
- DETECTION GAP UP TO .180"
- TRUE 0 SPEED, AND NEAR 0 SPEED OPTIONS
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CHOPPER AND NON CHOPPER OPTIONS
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 7
|
Speed and Direction Magnet Sensor
|
- 2 OUTPUTS FOR SPEED (OR COUNT) & DIRECTION
- LINEAR OR ROTATIONAL MOVEMENT
- DETECT MOVING MAGNETS
- HALL EFFECT AND MAGNETORESISTIVE
- DETECTION GAP UP TO 3"
- TRUE 0 SPEED TO 20,000 Hz
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 8
|
Dual Output Hall Switch Sensor
|
- DETECT MAGNETS OR MAGNETIC FIELDS
- 2 OUTPUTS: N POLE, AND S POLE
- TRUE 0 SPEED TO 20,000 PULSES PER SECOND
- DETECTION GAP DEPENDS ON MAGNET SIZE, UP TO 3"
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- HALL EFFECT TECHNOLOGY
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 9
|
Hall Latch Sensor
|
- DETECT MAGNETS OR MAGNETIC FIELDS
- 1 DIGITAL OUTPUT, S POLE ON, N POLE OFF
- HOLDS THE LAST STATE WHEN THE MAGNET LEAVES
- GOOD FOR RING MAGNET ROTATIONAL SPEED
- TRANSISTOR OUTPUT OR RELAY CLOSURE
- DETECTION GAP UP TO 3"
- TRUE 0 SPEED TO 20,000 Hz
- DC POWERED, 4.5 TO 30 VOLTS
- POTTED, RUGGED, -40 TO 150 DEG C
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 10
|
Shot Rod Sensor
|
- SPECIFIC SENSORS FOR DIE CAST SHOT ROD SENSING
- DIRECT REPLACEMENTS AND IMPROVED VERSIONS
- DETECT THREADED RODS, SPEED AND POSITION
- 2 PULSES PER TOOTH 90 DEGREES OUT OF PHASE
- DURABLE FACE, AND EXTENDED GAP VERSIONS
- NEW SEALING TECHNOLOGY EXTENDS LIFE
- 20 TPI, 10TPI, 2MM AND 1MM VERSIONS
- DETECTION GAP .000" TO .030"
- RUGGED, WIDE TEMPERATURE RANGE
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 11
|
Digital Ferrous Metal Detection Sensor
|
- DETECT FERROUS OBJECTS AS SMALL AS A PIN HEAD
- DETECT THROUGH ALUMINUM
- DIGITAL OUTPUT
- DETECTION GAP DEPENDS ON TARGET SIZE, UP TO 1.4"
- TRUE 0 SPEED TO 6,000 PULSES PER SECOND
- OPERATE FROM A DC POWER SUPPLY, 8 TO 30 VOLTS
- SOLID STATE HALL EFFECT
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 12
|
Analog Ferrous Metal Position Sensor
|
- DETECT FERROUS OBJECTS AS SMALL AS A PIN HEAD
- DETECT THROUGH ALUMINUM
- SCAN FOR FERROUS TARGET MOVEMENT OR POSITION
- ANALOG OUTPUT INCREASES WITH PROXIMITY
- TRUE 0 SPEED TO 6,000 PULSES PER SECOND
- DETECTION GAP DEPENDS ON TARGET SIZE, UP TO 2.5"
- DC POWERED, 8 TO 30 VOLTS
- SOLID STATE HALL EFFECT
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 13
|
Variable Reluctance Sensor
|
- VARIABLE RELUCTANCE PASSIVE DEVICE
- NO POWER REQUIRED
- DETECT GEAR TEETH, 0-64 PITCH
- DETECT OTHER FERROUS TARGETS
- AMPLITUDE INCREASES WITH SPEED
- UP TO TO 10,000 TEETH PER SECOND
- -40 TO 200 DEGREES C
- NO ORIENTATION IS REQUIRED
- EXPOSED OR BURIED POLE PIECE OPTIONS
- 100 OHM OR 1K OHM COIL OPTIONS
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 14
|
Analog Hall Sensor
|
- ANALOG OUTPUT VARIES WITH FIELD STRENGTH
- DETECT DISTANCE TO MAGNET UP TO 2"
- DETECT POSITION OF MAGNET UP TO 3"
- DETECT MAGNETIC STRENGTH AND POLARITY
- CONTINUOUS AND PROGRAMMABLE VERSIONS
- POTTED, RUGGED, -40 TO 150 DEG C
- DC POWERED, 4.5 TO 30 VOLTS
- CLICK PICTURE TO SEE OPTIONS
|
|
CHOICE 15
|
Reed Switch
|
- NO POWER REQUIRED, 2 WIRE SWITCH
- CLOSES FROM EITHER POLE N OR S
- SWITCH DC OR AC LOADS, UP TO 1 AMP
- NORMALLY OPEN OR NORMALLY CLOSED MODELS
- 0 TO 500 Hz SWITCHING SPEED
- DETECTION GAP UP TO 3"
- POTTED AND SEALED
- RUGGED, WIDE TEMPERATURE RANGE
- CLICK PICTURE TO SEE OPTIONS
|
|
|
